« previous next »
Pages: 1 2 3 [4] 5 6 7   Go Down

Author Topic: KYLE"S 54 REBUILD  (Read 42999 times)

Offline kpm

  • Sr. Member
  • ****
  • Posts: 271
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #45 on: January 25, 2011, 07:52:59 pm »
well the diff has been rebuilt,and put back in as well as the motor and tranny.Gary fabricated an exhaust and heat sheild..to keep direct heat away from the starter.New motor and tranny mounts were also made,as well asmetal covers for the sides of the diff,and a lift out slide plate for starter acess.
  The disc brake is machined and fabricated into place...we are beefing up the drive shaft a little and will be putting it back in this week.The new bushings have been installed on the axcel's as well as new boogies and chains.The new sprockets are on.
  New fuel pump starter water pump distributor,cap rotor wire,plugs,carbrator,fan belt ,alternator..and mounting bracket.
...new wiring will begin soon too..lol..I hope..will add more info as progress is made!!!
                                        kpm
Logged

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #46 on: January 26, 2011, 12:12:11 pm »
Logged
after covering a few acres of prime real estate.

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #47 on: January 26, 2011, 02:20:06 pm »

  KPM do you have any pics of the other side of the brake assembly and how is the rotor held on ??
Logged
after covering a few acres of prime real estate.

Offline kpm

  • Sr. Member
  • ****
  • Posts: 271
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #48 on: January 26, 2011, 07:03:40 pm »
...I appreciate the extra effort Claude...I hope your feeling 100%..
  i'll take some more pictures of the brake set up for you.Started wiring today...strecthing boogies...will start putting the rubber on real soon.
                                                           kpm
Logged

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #49 on: February 07, 2011, 07:33:57 am »
  ANOTHER FANTASTIC UPDATE FROM KPM.

  Here is his email.

hi claude
              keep plugging away everyday...today had the whole crew working!!
..it's not hard to put mega hours in when doing a   rebuild on a bombardier...gotta luv it!!!
....some people question the cost of these machines(when done right)..it's easy to sink the money into them,then  factor in your time..lol..you better have a passion for i!!
   Gary keeps it all in perspective,which makes the job go smooth...like i've said before he's the wizard...had dashes made up by D.PAULSON of WADENA STEEL...the man does an excellant job...course you can see that by looking at the awesome job he has done on his wide gauge rebuild....hoping to drive this narrow at the rally!!!
                                                                          take care my friend
                                                                                                            kpm




http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1261.jpg

http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1254.jpg

http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1234.jpg

http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1250.jpg

http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1237.jpg






  
« Last Edit: February 07, 2011, 07:45:33 am by the old trucker »
Logged
after covering a few acres of prime real estate.

Offline viking

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #50 on: February 08, 2011, 05:24:00 am »
Kyle, Take a look at the remote oil filter kits. Make things pretty tidy during the oil changes.
Logged
Gimli, where men are men and fish are scared!

Offline kpm

  • Sr. Member
  • ****
  • Posts: 271
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #51 on: February 08, 2011, 08:22:33 am »
Dave
       we had checked them out,and decided to go with the stubby filter...made up a funnel type thingy..lol.for the oil to run into.
...less hoses to contend with..
                                                      kpm                                             
Logged

Offline grfishmaker

  • Full Member
  • ***
  • Posts: 213
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #52 on: February 12, 2011, 09:19:49 pm »
Well Kyle, it's plain to see what you've been spending your time at this winter. Now I understand why I haven't seen you out wheeling n' dealing on bombers this past few months. lol
You are going to have one fine machine when you are done. Sounds like you are going over it and sparing no shortcuts in her rebuild. Good work and also good job on getting Claude post your progress; otherwise he'd probably get himself into some sort of trouble.
Keep it up there Kyle.
Logged

Offline kpm

  • Sr. Member
  • ****
  • Posts: 271
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #53 on: February 12, 2011, 10:37:05 pm »
...thanx Gary.....
                               kpm
Logged

Offline kpm

  • Sr. Member
  • ****
  • Posts: 271
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #54 on: February 13, 2011, 01:04:12 pm »
..as u can see by the picture we work according to Manitoba safety standards!!!
                                                         lol...kpm
Logged

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #55 on: February 13, 2011, 06:18:31 pm »

  Update from the honorable KPM...

well Claude
                  the master clyinder is in place,shroud is built...the ceiling is insulated and polyed,so work on the inside is under way.Still LOTS to do...though it is coming together nice!!....hope to take her to the rally..
                                                       kyle


http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1272.jpg

http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1271.jpg

http://i333.photobucket.com/albums/m366/theoldtrucker/KPM1268.jpg
Logged
after covering a few acres of prime real estate.

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #56 on: February 13, 2011, 06:22:04 pm »

 Kyle what did you use for insulation ? Some sort of spray on type  ???    OT.
Logged
after covering a few acres of prime real estate.

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #57 on: February 14, 2011, 08:15:23 am »
Quote from: kpm on January 25, 2011, 07:52:59 pm
well the diff has been rebuilt,and put back in as well as the motor and tranny.Gary fabricated an exhaust and heat sheild..to keep direct heat away from the starter.New motor and tranny mounts were also made,as well asmetal covers for the sides of the diff,and a lift out slide plate for starter acess.
                                        kpm

  KPM when you rebuilt your diff can you tell me what parts you needed & what place you got them ? I need what they call a nest kit. (spider gears) for mine. Also Glen's newbuild needs the same thing. My diff is smaller than Glen's.
 Here is mine.  http://i333.photobucket.com/albums/m366/theoldtrucker/DSCF0373.jpg

Here is Glen's. http://i333.photobucket.com/albums/m366/theoldtrucker/PICT0850.jpg
Logged
after covering a few acres of prime real estate.

Offline kpm

  • Sr. Member
  • ****
  • Posts: 271
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #58 on: February 14, 2011, 08:43:46 am »
..i used strofoam 1''...and foam insulation to seal it in...
.....my diff is a 1 ton ...newer dodge.....and I bought my parts from piston and ring in wpg. mb...
.....grfishmaker bought a new factory diff from me for a narrow...i'm not sure he would want to sell...as he has 2 narrows of this own...and 2 wides for the record..
                                                                                         kpm
Logged

Offline the old trucker

  • Hero Member
  • *****
  • Posts: 1461
    • View Profile
Re: KYLE"S 54 REBUILD
« Reply #59 on: February 14, 2011, 11:42:52 am »


     Would you have a phone ### for those guys ??      OT.
Logged
after covering a few acres of prime real estate.
Pages: 1 2 3 [4] 5 6 7   Go Up
« previous next »